RWA-SP-JWH-001 by jwiv
RWA-SP-JWH-001.zip - 335 Kb
A scenario for Stevens Pass using RWA donationware
Bit longer than I intended, but so it goes. 90 minute run, uses bases RWA and Stevens Pass gear.
Start off in Delta Yard, pick up four empty centerbeams and run out to Snohomish Mills where you'll swap out the empty cars for loaded freight. You'll also pick up a set of boxcars from Snohomish Coop.
Once complete, you'll head directly to the South Portland Terminal.
Route:- Stevens Pass
Scenario:- RWA-SP-JWH-001
Description: Working out of the Delta yard, service Snohomish Mills and head to the Everett Port Terminal.
Briefing:
Working out of the Delta yard, service Snohomish Mills and head to the Everett Port Terminal.
Start Time: 0930
Duration: 90
Season: SEASON_SPRING
Service: RWA 2153
Initial Rolling Stock:-
2153
Instruction: We'll be starting off with grabbing a set of empty centerbeams to take out to Snohomish Mills. Once there, we'll have to swap them for loaded centerbeams, which will take a bit of back and forth since we won't have an empty siding to work with. We're also picking up a set of boxcars out of Snohomish Coop, then driving it all over to the Port Terminal. Traffic on the main lines should be fairly light, but there is a cut of tank cars passing through early this morning that we may run into on the way out.
At Location: (S) Delta Storage 1
Operation: Couple to back of train
Wagon Numbers:-
562294 562447 562112 561237
Instruction: We're connected and air hoses are in place. Looks good.
At Location: That's Snohomish Mills to our left. Pull ahead to the junction entrance, then reverse into the sidings. Switches here will be manual.Once in the yard, we will be swapping out full centerbeams for empties.
At Location: (S) Snohomish Mills Entrance
Operation: Default
At Location: Snohomish Mills 1
Operation: Couple to back of train
Wagon Numbers:-
561047 562490
Instruction: We're coupled up. Pull ahead forward, flip the switch, then reverse back into the other siding.
At Location: Snohomish Mills 2
Operation: Drop off wagon(s)
Wagon Numbers:-
561047 562490
Instruction: Okay, the first siding is now clear. Pull ahead forward to clear the switch, then reverse back into it. We'll be dropping all four empty cars there.
At Location: Snohomish Mills 1
Operation: Drop off wagon(s)
Wagon Numbers:-
562294 562447 562112 561237
Instruction: Now that we've got our load built and the empties dropped off, we need to pick up the loaded centerbeams and then split the empty centerbeams between both sidings.
At Location: Snohomish Mills 2
Operation: Couple to back of train
Wagon Numbers:-
561395 561112 562490 561047
Instruction: Now that we have our load picked up and emptied SM 2, go ahead and pick up the first two empty centerbeams from SM1.
At Location: Snohomish Mills 1
Operation: Couple to back of train
Wagon Numbers:-
562112 561237
Instruction: Okay, looks good. Lets drop these off at SM2 and move on.
At Location: Snohomish Mills 2
Operation: Drop off wagon(s)
Wagon Numbers:-
562112 561237
Instruction: Good work on swapping out everything. Now, pull out of the sidings. We're going to have to reverse down the main a bit in order to be able to pick up the rest of our load.
At Location: Once we're fully clear of the switchover, come to a stop and then pull forward through Snohomish Junction West 2.
At Location: DET MP 1776.2
Operation: Default
At Location: Snohomish Jct. West 2
Operation: Default
At Location: Woodinville Sub to Black River
Operation: Default
At Location: Snohomish Coop
Operation: Couple to back of train
Wagon Numbers:-
150223 150006 150240 150279
Instruction: We're all set here. Pull ahead forward to clear the switches, then we'll reverse out back to the main to get turned around.
At Location: Okay, once we're clear, set the switches and reverse onto the main.
At Location: Woodinville Sub to Black River
Operation: Default
At Location: Clear the switches and come to a stop. You should then be clear to proceed forward towards the Port Everett Terminal. There is some port traffic, so pay attention to your signals as you near the terminal.
At Location: Snohomish Jct. East
Operation: Default
At Location: Clear the junction, then reverse onto the center track in order to enter the terminal.
At Location: (S) Everett Main Switchover
Operation: Default
At Location: As you approach Terminal Gate B, you may need to manually set the switch to enter into the port. Also, be aware you will need to reduce speed to allow the gate protecting the port to fully open (approximately 5 mph).
At Location: (S) Terminal Gate Approach
Operation: Default
At Location: Pacific Terminal Gate B
Operation: Default
Instruction: Great work!
At Location: (S) Everett South Terminal B 2
Operation: Default
Final Destination: (S) Everett South Terminal B 2
Please remember even those this file is free, the author still has rights to the file. Be sure to read the readme that is enclosed for further copyright information and instructions to install the file.
DTG's Required Disclaimer
"IMPORTANT NOTICE. Everything on this site is user generated content designed for use with RailSimulator.com Limited’s train simulation products, including RailWorks 4: Train Simulator 2013, Train Simulator 2014 and Train Simulator 2015. RailSimulator.com Limited does not approve or endorse this user generated content and does not accept any liability or responsibility regarding it.
This user generated content has not been screened or tested by RailSimulator.com Limited. Accordingly, it may adversely affect your use of RailSimulator.com’s products. If you install this user generated content and it infringes the rules regarding user-generated content, RailSimulator.com Limited may choose to discontinue any support for that product which they may otherwise have provided.
The RailWorks EULA sets out in detail how user generated content may be used, which you can review further here: www.railsimulator.com/terms. In particular, this user generated content includes work which remains the intellectual property of RailSimulator.com Limited and which may not be rented, leased, sub-licensed, modified, adapted,copied, reproduced or redistributed without the permission of RailSimulator.com Limited."
We have 2139 guests and no members online