Amtrak GE Dash 8-32BWH Pepsi Can Comprehensive Mod Pack Released

[FanRailer]

READ FIRST (EXPAND):
Section 1: 0:00 - 17:58 (Phase V w/ HEP sounds on NEC)
Section 2: 17:58 - 27:59 (File manipulation)
Section 3: 27:59 - 48:54 (Pepsi Can w/ no-HEP sounds on San Diegan)
You tell me which sounds better =)

This is the Amtrak GE Dash 8-32BWH Sound & Physics Modification pack version 1.0

In order to utilize this freeware physics upgrade, you must have purchased the "Train Simulator: Amtrak Dash 8-32BWH Loco Add-On" pack available at Steam: http://store.steampowered.com/app/376931/

This is a freeware pack; in no way is it to be used for commercial purposes. You are free, however to further modify the physics enhancements found in this pack for personal use if you so choose.

This is both a sound AND physics mod.

The purpose of this pack is to adjust the traction characteristics values for more realistic operation. It additionally replaces the default horn and bell sounds with files that are authentic to the locomotive.

This pack includes the option to operate with or without HEP (changes acceleration characteristics and prime mover sounds).

Credits to Callum Beatson for the no-HEP engine sounds and sound code, and to Chris Reynolds (MilwaukeeNorth418) for the new K5LA horn recording.

General Parameter Change Log:
1. Weight set to 274,890 lbs.
2. Traction characteristics adjusted; see below for more details.
3. Dynamic brake values enhanced.
4. Blend air-dynamic brake delay increased to 10 seconds (originally set at 0).
5. Replaced horn/bell sounds.
6. Includes no-HEP sound pack.
7. Removed coupler slack on Superliner cars.

Technical specifications for the Amtrak Dash 8-32BWH:
1. GE Dash 8-32BWH (GE 7FDL-12; 3300 GHP); HEP version
a. Starting tractive effort of 60,260 lbs (268.054 kN)
b. Continuous TE of 38,500 lbs (171.26 kN) @ 26 mph
c. Wheel horsepower of ~2,450 hp (~1,830 kW) @ 30 mph; assuming ~200 kW HEP load
d. Maximum traction amps = 1800 (60,260 lbs)
e. Dynamic Brake effort of 37,390 lbs (166.319 kN) from 41 mph to 9 mph
f. DB resistor grid rating of 4,084 hp (3,047.76 kW)
g. Max brake amps = 900 (37,390 lbs)
h. Maximum speed of 103 mph
i. Engine RPM range = 400 - 1050
j. RPM change rate (rpm/second) = 20
k. Fuel consumption range (gph)= 4 - 158
l. Fuel capacity = 1,800 gallons
m. Weight = 122.71875 imperial tons (274,890 lbs)

2. GE Dash 8-32BWH (GE 7FDL-12; 3300 GHP); no HEP version
a. Wheel horsepower of 3,000 hp (2,239 kW) @ 30 mph
b. All other characteristics unchanged

IMPORTANT; Install Instructions

1. Locate Dash8_32BWHPack01 (C:\Program Files (x86)\Steam\SteamApps\common\RailWorks\Assets\DTG\Dash8_32BWHPack01)
2. Open DTG_Amtrak_Dash_8-32BWH_Sound_And_Physics_Mod_Pack.rar
3. Drag the file folders from the .rar in step 2 into the directory you opened in step 1.
4. The installation should be complete. Run TS2016 to check.
5. If installation is botched or does not work, to back up to original files, delete the folders from step 3.

User's Manual:
Upon installation, the pack defaults to using the HEP physics and sounds. In order to switch physics/sounds, follow the steps below:

1. Open the following directories:
a. "C:\Program Files (x86)\Steam\SteamApps\common\RailWorks\Assets\DTG\Dash8_32BWHPack01\RailVehicles\Simulation"
b. "C:\Program Files (x86)\Steam\SteamApps\common\RailWorks\Assets\DTG\Dash8_32BWHPack01\Audio\RailVehicles\Diesel\Dash8_32BWH\Engine"
2. In each of those directories, you will see two folders (one for each set of locomotive physics/sounds):
a. "HEP"
b. "No HEP"
3. Once you choose which set of physics/sounds to use, open the respective type folder in both directories from step 1.
4. Copy (CTRL + C) all files you find in the opened folder located in directory 1a.
5. Proceed back to directory 1a and paste (CTRL + V) the copied files into the directory; overwrite (replace) when prompted.
6. Copy (CTRL + C) all files you find in the opened folder located in directory 1b.
7. Proceed back to directory 1b and paste (CTRL + V) the copied files into the directory; overwrite (replace) when prompted.
8. If the previous 7 steps were completed properly, the physics swap should be successful; run TS2016 to check.

For adventurous players/developers, there are actually two sets of no-HEP notch 8 engine sounds included. If you can figure out how to swap between those two subsets, then have fun and decide for yourself which sounds better.

Thank you for downloading and installing.
Enjoy =)

Download Link: http://www.mediafire.com/download/h8rbr ... d_Pack.rar

Facebook Page: http://www.facebook.com/FanRailerMODS/

[bpetit]

Thanks for this.

[FanRailer]

Always a pleasure

[FanRailer]

Mediafire is being difficult at the moment; if the link does not get repaired before the weekend, look for the local file upload.

[skaliwag66]

Another amazing mod.

Excellent new horn too!

[FanRailer]

Link is live locally: http://railworksamerica.com/index.php/d ... =25:sounds

[WCL6655]

Fix the bell so when you turn on the bell you dont hear the loud noise of the engine sound that goes with it

[crocs4022]

Fix the bell so when you turn on the bell you dont hear the loud noise of the engine sound that goes with it

Demanding much?

[WCL6655]

Fix the bell so when you turn on the bell you dont hear the loud noise of the engine sound that goes with it

Demanding much?

No...Its just the bell...Not asking for more

[FanRailer]

If you can get me a clean recording of a Dash 8-32BWH bell playing without the engine on in the background, I'd be happy to update. I work with the best files I can get my hands on, and what is currently released is such.

[ErikGorbiHamilton]

If you can get me a clean recording of a Dash 8-32BWH bell playing without the engine on in the background, I'd be happy to update. I work with the best files I can get my hands on, and what is currently released is such.

I can provide you a edit i did. Has the old 80's-90's sounds GE bell in it. Ill send ya the file.