Railworks America

Posted: **Thu Jan 11, 2018 8:14 pm**

Hi, I used the engine repaint CN-F7 zebra, since I don't like the horn sound of the required F7 from DTG Feather river I tried to change the horn files by the UP SD-45 without success. Several hours lost to try and try but no result, always the same original sound of the F7 within the Feather river AP file. I used RW_tools and 7Z to extrack the files by the way. I read all topics about that in the forums. Now I'm done. Any help welcome!! **!!bow!!**

Posted: **Thu Jan 11, 2018 8:36 pm**

Not quite sure which files you are changing but you need to go into the CN engine bin file and near the bottom it will cal out the horn. You need to change the provider and folder to whatever you want it to look at. Make sure you check whatever it's supposed to be looking at or you won't get the sound.

horn sound.jpg

Posted: **Thu Jan 11, 2018 9:26 pm**

I will try to help further, to what Buzz has started.
That would be the code to replace the F7 horn by the DTM SD45-UP:

Code: Select all: <BlueprintID> <iBlueprintLibrary-cAbsoluteBlueprintID> <BlueprintSetID> <iBlueprintLibrary-cBlueprintSetID> <Provider d:type="cDeltaString">DTM</Provider> <Product d:type="cDeltaString">SD45-UP</Product> </iBlueprintLibrary-cBlueprintSetID> </BlueprintSetID> <BlueprintID d:type="cDeltaString">Audio\Horns\SD45\SD45 Horn.xml</BlueprintID> </iBlueprintLibrary-cAbsoluteBlueprintID> </BlueprintID>

Basically you edit only three lines in that CN repaint: provider, product and path to the "horn driver" file.

Posted: **Thu Jan 11, 2018 10:54 pm**

buzz456 wrote:Not quite sure which files you are changing but you need to go into the CN engine bin file and near the bottom it will cal out the horn. You need to change the provider and folder to whatever you want it to look at. Make sure you check whatever it's supposed to be looking at or you won't get the sound.
horn sound.jpg

Many thanks for your help! Well, I never thought that I had to edit this file!! Then if I understand correctly I have to change these lines by the right provider? In my file It's written:
<BlueprintID d:type="cDeltaString">RailVehicles\Couplings\Buckeye\Type-E\buckeye_type_e_coupling.xml</BlueprintID>
The word "audio" is not mentioned.

Posted: **Thu Jan 11, 2018 11:00 pm**

jalsina wrote:I will try to help further, to what Buzz has started.
That would be the code to replace the F7 horn by the DTM SD45-UP:

Code: Select all
<BlueprintID> <iBlueprintLibrary-cAbsoluteBlueprintID> <BlueprintSetID> <iBlueprintLibrary-cBlueprintSetID> <Provider d:type="cDeltaString">DTM</Provider> <Product d:type="cDeltaString">SD45-UP</Product> </iBlueprintLibrary-cBlueprintSetID> </BlueprintSetID> <BlueprintID d:type="cDeltaString">Audio\Horns\SD45\SD45 Horn.xml</BlueprintID> </iBlueprintLibrary-cAbsoluteBlueprintID> </BlueprintID>

Many thanks for your help!! I try to edit this file and will let you know!
Basically you edit only three lines in that CN repaint: provider, product and path to the "horn driver" file.

Posted: **Fri Jan 12, 2018 12:15 am**

Well, does'nt work either !**conf**!

I read somewhere that I should repack Feather River assets in AP file after the modifications, is it the case?
!*hp*!

Posted: **Fri Jan 12, 2018 2:05 am**

So sorry, I edited the file at the wrong place !DUH!

I made the correction but now, no horn sound at all !!! !*hp*!

Any idea? I'm near of success thank to you guys !!howdy!!

Posted: **Fri Jan 12, 2018 2:49 am**

By the way, the bell does'nt work either...

Posted: **Fri Jan 12, 2018 5:17 pm**

I stop guessing, can't change the horn sound *!embar*!

If anyone had changed the horn sound of this engine successfully after installing the CN F7 zebra repaint, please get in touch with me for help! I give my tong to the cat...

Posted: **Fri Jan 12, 2018 7:30 pm**

This may be a dumb question but did you check the DTM locomotive after you told it that was the horn it's supposed to be looking for? I did exactly what you showed above and it works just fine.

Posted: **Fri Jan 12, 2018 7:32 pm**

jtousign wrote:Well, does'nt work either I read somewhere that I should repack Feather River assets in AP file after the modifications, is it the case?

No.

Posted: **Fri Jan 12, 2018 8:33 pm**

quote]did you check the DTM locomotive after you told it that was the horn it's supposed to be looking for?[quote]

Yes I did and That is the horn sound I'd love to get for the CN F7. Instead I always hear the dern horn sound of the original F7 from DTG FR. I probably missed something important when I extracted thefiles from AP FR, I don't know !*don-know!*

Posted: **Fri Jan 12, 2018 8:53 pm**

Well your wording looks correct. Extract the F7 from the .ap. Path should look like this.

FR F7.jpg

Posted: **Sat Jan 13, 2018 12:52 am**

That's exactly the same path as me. I notice that you have the Via rail F7 engine??? Where can I find the repaint please? Thanks a lot for your help! !*salute*!

Posted: **Sat Jan 13, 2018 12:54 am**

OK I just found it in the file library!

Railworks America

Changing horn does'nt work

Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work

Re: Changing horn does'nt work