Railworks America

Hey everybody,

normally I don't have problems to make a copy of any engine for repainting it without loosing the original loco.
But now I'm a little bit confused and frustated. Why the heck I don't get these loco copied ?
Everything I try failed. Don't shown in selection...no name...no loco...nothing. Maybe someone has copied this succsessful and can send me a tip or a copy of the bin file.

Kindly Sibell

I think probably your problem is to do with the .ap. If you have your new named folder and the new bin done and it's not showing up try making the .ap a .ap.xxx and see if the loco shows up. It's that and or in the line about the geometry. If you don't get it to work post back and I'll look at the wording on those two lines.

Hey buzz.

I tried every step you said, but nothing works.

The name of my locomotive is IC and it's in the SD70M folder. Here is the bin folder. Let me know if this works please.

It works, but the loco have no numbers, no sound, no horn sound, engine sound, break sound etc.
But now I have to study which fault I've done...maybe I forget a line to edit...hm...don't know

My bad sorry. If you used my bin file and just changed the lines to get your paint to show up I used some modified sounds for my locomotive. 3/4 of the way down there is a EngineSound entry.
Says:
<ChildName d:type="cDeltaString">EngineSound</ChildName>
<BlueprintID>
<iBlueprintLibrary-cAbsoluteBlueprintID>
<BlueprintSetID>
<iBlueprintLibrary-cBlueprintSetID>
<Provider d:type="cDeltaString">RSC</Provider>
<Product d:type="cDeltaString">SD70Pack01</Product>
</iBlueprintLibrary-cBlueprintSetID>
</BlueprintSetID>
<BlueprintID d:type="cDeltaString">Audio\RailVehicles\Diesel\SD70ACe\70a-Helper Engine Sound.xml</BlueprintID>


Needs to say:
<ChildName d:type="cDeltaString">EngineSound</ChildName>
<BlueprintID>
<iBlueprintLibrary-cAbsoluteBlueprintID>
<BlueprintSetID>
<iBlueprintLibrary-cBlueprintSetID>
<Provider d:type="cDeltaString">RSC</Provider>
<Product d:type="cDeltaString">ShermanHill</Product>
</iBlueprintLibrary-cBlueprintSetID>
</BlueprintSetID>
<BlueprintID d:type="cDeltaString">Audio\RailVehicles\Diesel\SD70M\Engine\SD70MEngineSound.xml</BlueprintID>

The only things you need to change are under product type should be ShermanHill and under Audio change it to SD70M\Engine/SD70MEngineSound.xml.
It should work then.

Ok, maybe I'm really stupid or u do things with the .bin I don't understand. Your .bin file is 23 kb big, after edit the 2 lines I apply it to serz to save the new informations.
After that, my .bin is only 1 kb small and the loco doesn't work.
This is the first time I really have problems with that. Freaky haha

I want this loco with sound and with the right name, but if I change IC to CSX...FAIL...loco don't shown up.

Is that what you want it to be called? Just CSX? If so I will make you a complete bin and send it to you.

No, after I understand that u edit the numbers I hae to do more of it with more numbers set by myself. So make pls more bins...maybe 4 with several numbers pls.
One from the screenshot and others from the internet maybe. Thx for your help.

Check your PM.

Works fine icluding the sound, great job thx buzzi

Edit: Oh I've seen that I now can use autonumbering, nice...more to do for me and less for u...because now I only need the one bin file, u are my hero now thx a lot *kiss*

buzz456 wrote:Is that what you want it to be called? Just CSX? If so I will make you a complete bin and send it to you.

In which file (bin) and line may I change the loco names that display in the scenario lists (as train name) or in the quick drive roster?

This is the top of the .bin file from the engine folder:

<?xml version="1.0" encoding="utf-8"?>
<cBlueprintLoader xmlns:d="http://www.kuju.com/TnT/2003/Delta" d:version="1.0">
<Blueprint>
<cEngineBlueprint>
<Name d:type="cDeltaString">Enter here name you want to use</Name>
<BrowseInformation>
<iRailVehicleBlueprint-cBrowseRVInformation>
<DisplayName>
<Localisation-cUserLocalisedString>
<English d:type="cDeltaString">Enter here name you want to use</English>
<French d:type="cDeltaString"></French>
<Italian d:type="cDeltaString"></Italian>
<German d:type="cDeltaString"></German>
<Spanish d:type="cDeltaString"></Spanish>
<Dutch d:type="cDeltaString"></Dutch>
<Polish d:type="cDeltaString"></Polish>
<Russian d:type="cDeltaString">EMD SD70M ОТЖД</Russian>

The red one is the name of the loco it will shown ingame.